Quantity: 1 - Color: Black - Material: Circuit board - NRF24L01 is a universal ISM band monolithic transceiver chip works in the 2.4-2.5GHz - Wireless transceiver including: Frequency generator enhanced type SchockBurstTM mode controller power amplifier crystal amplifier modulator demodulator - The output power channel selection and protocol settings can be set extremely low current consumption through the SPI interface - As the transmit mode the transmit power is 6dBm the current is 9.0mA the accepted mode current is 12.3mA the current consumption of the power-down mode and standby mode are lower - Built-in 2.4GHz antenna supports up to six channels of data reception - Size: 15 x 29mm (including antenna) - Low operating voltage: 1.9-3.6V - 125 channels multi-point communication and frequency hopping to meet the communication needs - High Rate: 2Mbps as air transmission time is very short greatly reducing collision phenomena in wireless transmission (air transfer rate of software setting: 1Mbps or 2Mbps) - Low power consumption: When the answer mode communication fast air transmission and start-up time which greatly reduces the current consumption - Low application cost: NRF24L01 integrated part of all high-speed signal processing related to RF protocol such as: automatic retransmission of lost packets and automatically generate response signals etc. - NRF24L01 SPI interface: hardware SPI port MCU I/O ports - Internal FIFO compatible with a variety of microprocessor interface micro-controller is convenient - Standard pin Dip2.54MM spacing interface for embedded applications - Packing list: - 1 x NRF24L01 wireless transceiver module
Arduino Si4432 433MHz Wireless RF Transceiver Module Low Power Consumption With Antenna Compatible With RPi
Model RFC-1100C Quantity 1 Color Blue Material PCB Features Use CC110L wireless RF chip fully compatible with CC1100/CC1101 more simple and stable; Programmable data speed: 0.6~600kbps (recommend range: 2.4kbps~500kbps); Working frequency range: 387~464MHz free ISM frequency band (recommend range: 430~436MHz); Modulation mode: 2-FSK 4-FSK GFSK and OOK; 64 bit receive and transmit; Can set address by software output data when receive the module's address; Can directly connects kinds of SCM for use; Convenient software programming; Low power consumption performance current consumption about 20uA when on sleep mode; Max transmit power: +20dBm; Quick start: 240uS; Fast switch. Specification Working temperature: 4.5~5.5V Max. transmitted power: +20dBm Max. data transmission: 500kbps output power: +20dBm working temperature: -40'C~85'C classical sensitivity / highest sensitivity: -110/-116dBm power down mode working current: 20uA: 65mA receive mode working current: 12.5mA. Application Great for DIY projects. English Manual/Spec Yes Packing List 1 x Wireless RF transceiver module 1 x High gain antenna Manual: http://m5.img.dxcdn.com/CDDriver/CD/sku.208524.docx
Model: UTC-1212SE - Color: Green - Material: PCB - Integrated SX1212 chipset - Low Rx power consumption: 3mA - Low Tx power consumption: 25 mA @ +10 dBm - Programmable RF output power: up to +12.5 dBm in 8 steps - Packet handling feature with data whitening and automatic CRC generation - RSSI (Received Signal Strength Indicator) - Incoming sync word recognition - Communication range: 300~500 meters - Standard 2.54mm pin pitch - Built-in Bit-Synchronizer for incoming data and clock synchronization and recovery - Working voltage: 2.1~3.6V - Working temperature: -40~85'C - Working humidity: 10~90% - Frequency: 390~470MHz - Transmit power: -8.5~12.5dBm - Transmission rate: 1K 2K 5K 10K 25K 40Kbps - Tx current: 34mA - Continuous Rx current: 3mA - Sleep current: 1.5uA - Max. sensitivity: -110dBm - Serial transmission rate: 1200/2400/4800/9600/19200/38400/57600bps - Max. data packet: 152byte - Configuration modification: 300k cycles - Comes with 10cm antenna
Arduino 2.4G NRF24L01+ Wireless Transceiver Module + SMA Antenna Microcontroll is available now from our US warehouse Free shipping to US in 3-6 business days ship to Canada, Brazil in 7-10 days NRF24L01 + 2.4G Wireless Transceiver Module + SMA Antenna MCU Arduino Description: NRF24L01 Basic characteristics: 2 Mbit / s rate of the peak current of 12.5mA received In the 2Mbit / s rate @ 0dBm output peak current of 11mA 400nA power down mode 32uA standby mode power consumption 130us fast switching and wake-up time With on-chip voltage regulator oltage regulators In the 1.9 to 3.6V low voltage operation MultiCeiverMT hardware provides simultaneous six receiver functions, 2Mbit / s high-quality VoIP makes it possible to 130 us quickly switch and wake time Has the on-chip voltage regulator oltage regulators Can work at 1.9 to 3.6 V low voltage Application: Mouse, keyboard, wireless headsets, smart sports equipment, remote controls, voice applications, safety devices, VOIP applications, remote control, telemetry, wireless meter reading, access control, systems, paging, industrial data acquisition systems, wireless tag. Identification, RF contactless smart cards, small wireless data terminals, fire safety systems, wireless remote control system. Systems, bio-signal acquisition, wireless 232, wireless 422/485 data communications. Package included: 1 x NRF24L01 + Wireless transceiver module
DRF1212D10 is a low-cost sub-1 GHz transceiver module designed for operations in the unlicensed ISM (Industrial Scientific Medical) and LPRD bands. FSK (Frequency Shift Keying) modulation/demodulation multi-channel operation high bandwidth efficiency and anti-blocking performance make DRF1212D10 modules easy to realize the robust and reliable wireless link. The module can be configured to work in different channels with 200 KHz space. It adopts high efficient looped interleaving EDAC (Error Detection and correction) coding with coding gain up to 3dB which keeps in advance in error correction and coding efficiency over normal FEC (Forward Error Correction) coding. Because of its high reliability in correction modules can filter error and fake information automatically and realize truly transparent wireless link which makes DRF1212D10 very suitable in the rigid communication environment. DRF1212D10 integrates two 256 bytes buffer. When the buffer is empty users can transfer nearly 217 bytes data per time and even limitless data transfer can be achieved as long as RF data rate (RF module to RF module) is configured to be faster than UART data rate (MCU to RF module). DRF1212D10 provides standard UART/TTL interface. Users can choose seven data rates and three parity checks which make DRF1212D10 possibly tailor-made for different applications. DRF1212D10 operates at 2.1~3.6V with extra low power consumption. The current in sleep mode can be minimized to 1.5uA and the current in receive mode no more than 4mA makes modules very suitable for battery powered-up applications. The part number in the picture is DRF1212D10-043A which is DIP package. For SMD package please check the DRF1212D10-043S1.