Brand N/A Model N/A Quantity 1 Color Red Material Plastic +PCB Specification Module Properties: polymer lithium battery protection board Overcharge detection voltage: 4.25 ± 0.025V Overcharge release voltage: 4.15 ± 0.05V Over discharge detection voltage: 2.50 ± 0.08V Overdischarge release voltage: 3.00 ± 0.1V Current :20-30A overcurrent Operating Current: 30A (natural cooling 10A additional heat sink 15A the maximum instantaneous current 30A) Features 3 series lithium battery protection board Application 3 series lithium battery protection board suitable for nominal voltage of 10.8V lithium battery 11.1V lithium battery pack 12.6V lithium battery pack. With automatic activation protection condition is restored automatically cancel the protection without charger activation easier to use English Manual/Spec N/A Keywords Module Properties: polymer lithium battery protection board; Overcharge detection voltage: 4.25 ± 0.025V; Overcharge release voltage: 4.15 ± 0.05V; Over-discharge detection voltage: 2.50 ± 0.08V; Over-discharge release voltage: 3.00 ± 0.1V Current :20-30A overcurrent; Working Current: 30A (natural cooling 10A additional heat sink 15A the maximum instantaneous current 30A) Packing List 1 x Board
Based on a current sensor module and based on the principle of the hall current which convert current into an analog voltage output; MCU (Arduino UNO R3) that includes AD converter can be read out and converted into measured current value; Suitable for SCM system powered by 5V power supply; Can measure AC and DC; Widely used in over-current detection current monitoring and other occasions.
Introduction The power supply is isolated industrial power supply built-in modules with temperature protection overcurrent and short circuit full protection AC 85~265V wide voltage input high voltage isolation 431 precisely regulated DC 24V output. Working temperature: -20 ~ 60 ° Relative humidity: 40 ~ 90% RH Input voltage range: 85 ~ 265VAC Input Current: 0.0273A (AC110V) 0.014 (AC220V) A Input inrush current: 20A Output Voltage: +24 V Maximum current: 200mA Peak current: 250mA Output voltage range: 23.80 ~ 24.2V Ripple: 150mV Output overvoltage: 23.8 ~ 24.3 Output Over Power Protection: Short circuit protection: Temperature protection: Overcurrent protection: Yes Installation 1. It can be installed at the input and output pins soldered directly on the PCB; 2. A plastic fixed.
100A DC Digital Multifunction Power Meter Energy Monitor Module Voltmeter Ammeter With 50A Shunt Description: Working Voltage DC 6.5V-100V Measuring Voltage DC 6.5V-100V Measuring Current 0-100A Rated Power 10000W Display LCD Display Format Power 0.0-999.9W (1KW) Energy 0-999Wh(10KWh) Voltage 6.50-99.99V Current 0.00-100.00A Shunt Voltage 75mV Current 50A Feature: 100A DC multifunction power meter with 50A shunt current LCD display wih backlight, easy to read Equipped with external shunt design, no extra needed Power, current, voltage and energy display and monitor timely easy to know electric energy consumption Electric energy clear function, perfect for various device monitor separately overload alarm function (over power alarm threshold, the backlight and voltage flashing alarm) Power memory, shave the power parameter when power down, safe to use Operaqtion Tips: 1. The backlight control By short press the button to turn on or off the backlight, In the bakclight mode,the data will automatically store when power down 2. The energy cleared Step 1: Press the power button 5 seconds until the digital display "CLr" then release the button; Step 2: Now it is in the "energy clear" mode, press the button again, the energy data is cleared and stop flashing; Step 3: If in the "energy clear" mode you do not press the button in 5 seconds,then the energy data will not be cleared 3. Set power alarm value Step 1: Press the button, when the power area display "SET " release button, Step 2:it is in the pweor alarming setting mode, the voltage area displays the highest value of the voltage alarm,the current area displays the lowest value of the voltage alarm. Then you can press the button quickly to increase the value" +1" when there is no key operation more than three seconds, Package included: 1X 100A Power Meter 1X Shunt
Use advanced synchronous rectifier controller and 3.7m ohms low impedance NMOS swith tube to high current and high efficiency DC-DC buck converter; Input voltage: 16~40V (rated 24V); Output voltage: 1.0~12V; Output current: 6A (Natural heat dissipation); Load starting current: rated 6A Max. 7A; Undervoltage overcurrent short circuit protection
An electronic brick is an electronic module which can be assembled like Lego bricks simply by plugging in and pulling out. Compared to traditional universal boards and circuit modules assembled with various electronic components electronic brick has standardized interfaces plug and play simplifying construction of prototype circuit on ones own. There are many types of electronic bricks and we provide more than twenty types with different functions including buttons sensors Bluetooth modules etc whose functions cover from sensor to motor drive from Ethernet to wireless communication via Bluetooth and so on. We will continue to add more types to meet the various needs of different projects. Electronic brick of current sensor is based on ACS712 sensor which can accurately detect AC or DC signals. The maximum AC or DC that can be detected can reach 5A and the present current signal can be read via analog I / O port. Features 1. Plug and play easy to use. Compatible with the mainstream 2.54 interfaces and 4-Pin Grove interfaces in the market. 2. With use of M4 standard fixed holes compatible with M4-standard kits such as Lego and Makeblock.3. Terminals with screws for easy wiring and removing. 3. Terminals with screws for easy wiring and removing. Specifications PCB size 30.0mm X 24.0mm X 1.6mm Working voltage 5V Input current type AC or DC Compatible interfaces 2.54 3-pin interface and 4-pin Grove interface(1) Wiring interface Power terminal(2) Note 1： S for analog output port V and G for voltage at the common collector and ground respectively Note 2: “+”for current inflow port“-”for current outflow port Electrical characteristics Parameter Min. Typical Max. Unit Supply voltage 4.5 5 5.5 VDC Working current（VCC=5V） - 10 13 mA Output impedance RLOAD（VIOUT to GND） 4.7 - - KΩ Bandwidth(1) - 34 - Hz Input current range -5 - 5 A Sensitivity 180 185 190 mV/A Note 1： After removing C1 bandwidth can reach 80kHz Relationship between output voltage and induced current
Current sensor chip: ACS712ELC-30A - Pin 5V power supply on-board power indicator - The module can measure the positive and negative 30A corresponding to the analog output 66mV/A. - There is no the detection current through the output voltage is VCC/2.
Model 20480 Quantity 1 Color Black + silver Material Plastic + current Specification Current: 20A; Voltage: 75mV; Temperature: -40~65'C; Humidity: 50A; temperature Features Shunt resistor for ammeter Application Perfect for DIY project Packing List 1 x Shunt resistor